ansys接触分析时,总是出现以下的警告：1.contact has experienced an abrupt change.2.large deformation effects are active which may have invalidated some of your applied supports such as displacement,3.the unconverged solution is output fo

来源：学生作业帮助网 编辑：作业帮 时间：2024/05/01 04:18:52
ansys接触分析时,总是出现以下的警告：1.contact has experienced an abrupt change.2.large deformation effects are active which may have invalidated some of your applied supports such as displacement,3.the unconverged solution is output fo

ansys接触分析时,总是出现以下的警告：1.contact has experienced an abrupt change.2.large deformation effects are active which may have invalidated some of your applied supports such as displacement,3.the unconverged solution is output fo
ansys接触分析时,总是出现以下的警告：
1.contact has experienced an abrupt change.
2.large deformation effects are active which may have invalidated some of your applied supports such as displacement,
3.the unconverged solution is output for analysis debug .
4.the solver engine was unable to converge on a solution for the nonlinear problem as constrained.
分析的是橡胶与塑料间被挤压,用的是ansys workbench,接触分析总是不收敛,找不出原因.

ansys接触分析时,总是出现以下的警告：1.contact has experienced an abrupt change.2.large deformation effects are active which may have invalidated some of your applied supports such as displacement,3.the unconverged solution is output fo
检查网格,检查接触及单元设置

1.接触经历了一个突然的变化。
2.large变形效果无效,而这有可能是活跃的你的一些应用支持如位移,,,,,
解决方法是:输出非线性分析调试....
(四)求解发动机无法聚集在解决的办法为约束的非线性问题。

请问你的问题解决了吗，我出现了跟你相识的问题，老是不收敛，不知道怎样设置？

ansys接触分析时,总是出现以下的警告：1.contact has experienced an abrupt change.2.large deformation effects are active which may have invalidated some of your applied supports such as displacement,3.the unconverged solution is output fo ANSYS接触分析时出现警告,Contact element 5301 ststus changes abruptly from contact -> no-contact.请高手指教：是什么原因产生的问题,如何解决, ansys划分网格出现如下图的警告；是怎么回事? 用Ansys静力学分析,都设好后sovle,即不出现警告也不出现solution is done怎么回事 ansys接触分析的问题solid-solid直接接触分析我用170、173接触对可以算,可是分析solid-shell的时候,总是会出现某些节点位移过大的问题.或者给一个shell单元的接触分析的例子. ansys workbench 14.5做接触分析出现警告,外面泵体是刚体,里面是橡胶衬套,在内部施加一均布载荷,分析其变形情况有人说是材料问题，换其他材料也不管用，也是出现警告，打开大变形也有警告 ansys静电结构耦合多物理场求解时,出现如下警告：element number 2897 has negative volume due to excessive distortion under morphing volume=-3349.3964 请问这是什么原因引起的?我的模型，进行静力学分析是没问题 ansys模态分析.最后求解时出现下面的警告：Element 1 has an undefined node number 0以及：Element 2 has an undefined node number 0,然后软件自动关闭 求教,ansys接触分析出现的警告提示?最后紫色线在青色线上方.算是收敛了吧1,Volume 85 is being meshed entirely with SOLID45 tetrahedra, which can be much less accurate than bricks. Use quadratic (10-node) tetrahedra if availab ansys警告 ANSYS做非线性静力分析,结构算到一半就出现以下警告,是不是因为荷载偏大混凝土开裂后的原因?求解!*** WARNING *** CP = 45693.891 TIME= 01:03:28 There are 2 small equation solver pivot term ansys分析中出现这个警告什么意思Real constant 1 referenced by at least element types 2 and 3. ansys划分单元格出现这个警告!如何处理 ansys workbench如何查看警告里出现的弱弹簧反力?如题,分析之后出现警告信息：One or more bodies may be underconstrained and experiencing rigid body motion.Weak springs have been added to attain a solution.Refer to Troubleshoot ANSYS WORKBENCH静力分析总是出现：an error occurred while starting the ANSYS solver module,最郁闷的是第二天机子重启后计算不出现这个问题了,可我什么都没改过呀? ansys问题 我在做ANSYS分析相变问题时总是运行几小时后ANSYS自动退出. 在做接触式逆止器的ansys分析,怎么定义接触对? ANSYS 出现这样的警告,如何修改?the memeory size requested[516mb]is not currentlu available.reenter ansys command line with less memory request