机械图纸上的英文请翻译下1.ALL SHARP EDGES&CORNERS ARE TO BE BROKEN WITH A.010 RADIUS,UNLESS OTERWISH SPECIFIED.2.ALL MACHINING SURFACES ARE TO BE 250 Ra(MAX)UNLESS OTHERWISS SPECIFED.3.ALL SEAL GROOVES MUST HAVE AND FINISH AS SHOWN.4.NO S

来源：学生作业帮助网 编辑：作业帮 时间：2024/05/09 13:41:40
机械图纸上的英文请翻译下1.ALL SHARP EDGES&CORNERS ARE TO BE BROKEN WITH A.010 RADIUS,UNLESS OTERWISH SPECIFIED.2.ALL MACHINING SURFACES ARE TO BE 250 Ra(MAX)UNLESS OTHERWISS SPECIFED.3.ALL SEAL GROOVES MUST HAVE AND FINISH AS SHOWN.4.NO S

机械图纸上的英文请翻译下1.ALL SHARP EDGES&CORNERS ARE TO BE BROKEN WITH A.010 RADIUS,UNLESS OTERWISH SPECIFIED.2.ALL MACHINING SURFACES ARE TO BE 250 Ra(MAX)UNLESS OTHERWISS SPECIFED.3.ALL SEAL GROOVES MUST HAVE AND FINISH AS SHOWN.4.NO S
机械图纸上的英文请翻译下
1.ALL SHARP EDGES&CORNERS ARE TO BE BROKEN WITH A.010 RADIUS,UNLESS OTERWISH SPECIFIED.
2.ALL MACHINING SURFACES ARE TO BE 250 Ra(MAX)UNLESS OTHERWISS SPECIFED.
3.ALL SEAL GROOVES MUST HAVE AND FINISH AS SHOWN.
4.NO SPRIRAL OR CHATTER TOOL MARKS ARE ALLOWED ON O-RING/BU-WASHER GROOVE SURFACES.
5.DEBURR&BREAK ALL EDGES
DO NOT SCALE DRAWING
6.DIMENSIONS ARE IN INCHES OR [MILLIMETERS]UNLESS OTHERSWISE SPECIFIED.
7.WELD CALL-OUTS+.06/.00
8.MAT'L WAS CAST IRON BAR,9-18-92,MOHR
9.REDREW ON AUTOCAD.NO CHANGD;ECN-12787,10-22-98,MAP

机械图纸上的英文请翻译下1.ALL SHARP EDGES&CORNERS ARE TO BE BROKEN WITH A.010 RADIUS,UNLESS OTERWISH SPECIFIED.2.ALL MACHINING SURFACES ARE TO BE 250 Ra(MAX)UNLESS OTHERWISS SPECIFED.3.ALL SEAL GROOVES MUST HAVE AND FINISH AS SHOWN.4.NO S
1 若非指定,所有的尖角都会被倒成半径为0.01的角.
2 若非指定,所有的机械表面粗糙度（最大）均为250.
3 所有封槽必须如图所示完成.
4 不允许在O型圈和垫圈的凹槽表面有任何螺旋或钻孔工具加工过的痕迹.
5 清理所有边缘的毛刺
不允许按比例缩放作图
6 若非指定,尺寸均为英寸或者【毫米】.
7 焊接维修+.06/.00
8 垫子为铸铁棒9-18-92,MOHR
9 用autocad重新生成NO CHANGD;ECN-12787,10-22-98,MAP
机械专业学生翻译的,因为没有图纸,没法跟英语相联系,已经尽力了.

机械图纸上的英文请翻译下1.ALL SHARP EDGES&CORNERS ARE TO BE BROKEN WITH A.010 RADIUS,UNLESS OTERWISH SPECIFIED.2.ALL MACHINING SURFACES ARE TO BE 250 Ra(MAX)UNLESS OTHERWISS SPECIFED.3.ALL SEAL GROOVES MUST HAVE AND FINISH AS SHOWN.4.NO S 谁能帮我看份英文机械图纸 (辊轴加工）帮我把图纸中英文翻译下也可以,最好是能看懂机械图纸了 机械图纸上的“all inside corner breaks to have 0.2'' radius” 机械图纸上的这个是什么意思? 英文 机械图纸上标注的公差是什么意思?pipe cap- brake mech piece partdecimals .x+ -1.5mm .x+ -380微米大家帮忙翻译一下,谢谢了! 英语翻译机械图纸上的,图中上面一行是德文,下面一行是英文! 翻译HOEKEN BREKEN（机械精加工图纸上标注的）在线等,急 20# SH/T3405 SMLS GB/T8163 等径三通 DN200 20# SH/t3405 SH/T3408 SCH20请分别介绍下上面的英文意思 raw edge机械图纸翻译 英语翻译Important Break all sharp edges around outer Swash & Trunnion bore with RO.1 to assist Electroless Nickel adhesion.Refer Step File for ectact 3D geometric description.求这两句的翻译,不要在线翻译的那种,机械图纸上的英 机械图纸上的英文缩写 还有ECN NO.REV在本图纸上，其余（RMN是Remain）什么作用？是装配关系吗？ 机械图纸上这段英文何意All welds shall be 6mm continuous or as noted 机械图纸上 4×R3 机械加工中图纸上的7h代表什么 机械加工里图纸上的平行四边形是啥意思? 机械图纸上的 angles vifs sharp corner 机械图纸上的cutter diameter centre是什么 机械加工图纸上的R3（典型）什么意思