英语翻译The algorithm for measuring the surface by the zero MH consists in the following.From initial point 1 (see Fig.2a,where n is "overtravel"),the MH travels to point 2 of the preliminary approach.From point 2,the MH moves at the rapid feed r

来源：学生作业帮助网 编辑：作业帮 时间：2024/05/03 01:55:29
英语翻译The algorithm for measuring the surface by the zero MH consists in the following.From initial point 1 (see Fig.2a,where n is

英语翻译The algorithm for measuring the surface by the zero MH consists in the following.From initial point 1 (see Fig.2a,where n is "overtravel"),the MH travels to point 2 of the preliminary approach.From point 2,the MH moves at the rapid feed r
英语翻译
The algorithm for measuring the surface by the zero MH consists in the following.From initial point 1 (see Fig.2a,where n is "overtravel"),the MH travels to point 2 of the preliminary approach.From point 2,the MH moves at the rapid feed rate of 500 mm/min until it makes contact with the controlled surface.At point 3,the MH is actuated for "coarse" measurement.Thereafter,the MH is withdrawn by 1.5 mm from point 3 to point 4.Subsequent- ly,the MH travels to the controlled surface at the rate of 8 mm/min.Point 5 is the stop for precision measurement.Point K is the end point for the measurement cycle,thereby de- termining the range of surface search.Values of travel rate for "coarse" and "precision" measurements are determined experimentally based on the required accuracy and minimum time for measurement.
Standard workpiece basing cycles are represented as subprograms written in macrolanguage of the NC device FANUC-6 made by the firm "Fanuk" I.Reference to workpiece-basing subpro- grams in the machining control program is executed by macrocommands.The user needs to know only the macrocommand structure in order to call the required subprogram.To illustrate,the macrocommand for calling the subprogram for automatic basing along axis Z appears as shown below:

英语翻译The algorithm for measuring the surface by the zero MH consists in the following.From initial point 1 (see Fig.2a,where n is "overtravel"),the MH travels to point 2 of the preliminary approach.From point 2,the MH moves at the rapid feed r
测量零的 MH 的表面的运算法则在于下列各项.从初次的点 1(见到图 2 a,哪里 n 是 " overtravel") ,MH 移动磨利初步方法中的 2 .从点 2 ,MH 用受约束的表面在 500 毫米／分的迅速输送率移动直到它接触点.在点 3 ,MH 为 " 粗的 " 测量被促使.其后,MH 从磨利 4 的点 3 被撤回 1.5 毫米.后来的－ ly,MH 以 8 毫米／分的率移动到受约束的表面.点 5 是精确测量的停止.点 K 是测量周的终点,藉此 de－ termining 多种表面的搜寻.旅行率的数值为”coar 还有不懂得问我 不要客气

该算法应用于测量表面由零MH在于以下。从初始点1(见图2a,那里的n是“overtravel”),MH旅行到2每点的初步探讨。从一个点2、MH动作,在快速喂入500毫米/分钟,直到它使接触表面的控制。在分3、MH驱动的“粗”的测量。此后,在1.5毫米MH撤出3点从一个点4。后续-...

全部展开

该算法应用于测量表面由零MH在于以下。从初始点1(见图2a,那里的n是“overtravel”),MH旅行到2每点的初步探讨。从一个点2、MH动作,在快速喂入500毫米/分钟,直到它使接触表面的控制。在分3、MH驱动的“粗”的测量。此后,在1.5毫米MH撤出3点从一个点4。后续-

收起

英语翻译The algorithm is not compared to other algorithms. 英语翻译3.PROPOSED ALGORITHM The proposed dynamic evolutionary algorithm exploits evolutionary progress history to adapt the current population to the new environment.The algorithm introduces shifts in the decision space,the so-called relocations algorithm THE ALGORITHM DESIGN MANUAL怎么样 英语翻译Position-based servo algorithm for aligning and positioning manipulator relative to the object and a model base grasping algorithm detected object pose is used 英语翻译Compared to the other two algorithms,the exponentiated algorithm has a rate θ associated with it.This rate needs to be set appropriately.In practice,we observed that the performance of the exponentiated algorithm is sensitive to the valu 英语翻译Artificial neural networks construction[ 5 ]We used the feed-forward multi-layer network for this work .The learning algorithm for our neural network is the widely used back-propagation algorithm.The fabric properties were the inputs to t 英语翻译The general framework for inference ingraphical model is the Junction Tree algorithm [32].The general Junction Tree algorithm mainlyconsists of constructing a junction tree from themodel and propagating probabilities acrossthe tree.The ef 英语翻译Limitations of the border tracking algorithm.The border tracking algorithm makes certain assumptions about the regions that it is tracking.Under what conditions could it fail to properly identify the border of a region?Figure 10.15:(Top l 英语翻译Write a recursive algorithm to find the combination of n objects taken k at a time using following definition. 英语翻译In this section we will evaluate the performance of VBMAR algorithm under different traffic patterns.VBMAR adopts three mechanisms,virtual channel,adaptivity,and load balance.These are constructs of the algorithm.We will not only evaluate 英语翻译B.Path Planning based on Dijkstra’s algorithmThe second software resource uses Breadth-first search(BFS) and Dijkstra’s algorithm.Breadth-first search(BFS) is a tree search algorithm used for traversing orsearching a tree or graph.The 英语翻译the application has encountered a probiem.We are sirry fo the incinvenience. 英语翻译for the diligent a week has seven todays,fo the slotful seven tomorrows 英语翻译：I gave several yanks to the starting cord fo the lawn mower. 英语翻译Thus,in numerical simulation,the contact algorithm is essential in preventing structural penetration so that the analysis can represent the true physical event. 英语翻译整句话是这样的：Before the data reconciliation algorithm was implemented in the distributed control system of the respective plant 英语翻译Jus the plain polo shirt would be great fo rnow thanks这句话是什么意思?